|
pomoc dla laika
|
| dawidt |
Dodano 05-04-2007 01:32
|
User
Posty: 52
Dołączył: 12/11/2006 17:47
|
witam
posiadam od 2 dni asus'a wl-500gp
pierwszy dzien siedzialem na oryginalnym sofcie
na drugi dzien wgralem olega
wszystko dzialo sprawnie i bezproblemowo[sprzet z podpisu, modem na bridge]
dzisiaj wgralem OPEN WRT [http://downloads.openwrt.org/whiterussian/0.9/default/openwrt-brcm-2.4-squashfs.trx]
i za nic nie moge skonfigurowac polaczenia przez WAN ;/
Moglbym prosic o gotowca w postaci pliku ktory musze podmienic w routerze ? ktos z Was zapewne posiada neostrade i poprawnie skonfigurowane polaczenie :]
z gory dzieki
pozdrawiam dawidt
Pozdrawiam
__________________________________
1000/1000@ER-X+2xArcherC7(AP)
|
| |
|
|
| Tom0000 |
Dodano 05-04-2007 08:37
|
User
Posty: 24
Dołączył: 24/02/2007 22:25
|
Czy zainstalowales wersje standard z pppoe czy jakas inna? Jesli jakas inna to musisz dodac pakiety potrzebne do pppoe.
Jesli masz wersje standard, wgraj rozszerzony interjfejs webowy. Polacz sie po www, skonfiguruj w zakladce network wan jako pppoe, podlacz modem i w zakladce status/pppoe sprawdz co sie loguje.
Asus 500gx
|
| |
|
|
| arteq |
Dodano 05-04-2007 09:05
|
VIP
Posty: 1918
Dołączył: 04/03/2006 17:42
|
Cytat Tom0000 napisał/a:
Czy zainstalowales wersje standard z pppoe czy jakas inna? Jesli jakas inna to musisz dodac pakiety potrzebne do pppoe.
Jesli masz wersje standard, wgraj rozszerzony interjfejs webowy. Polacz sie po www, skonfiguruj w zakladce network wan jako pppoe, podlacz modem i w zakladce status/pppoe sprawdz co sie loguje.
z całym szacunkiem, ale coś motasz. obraz domyślny ma juz PPPoE i nic nie trzeba wgrywac! Wystarczy skonfigurowac poprzez www, co prawda ubogie w stosunku do X-Wrt, ale internet da sie ustawić bez problemu.
Pozdrawiam, Artur
http://digi-led.pl Elementy elektroniczne | urz?dzenia sieciowe | us?ugi informatyczne
http://openwrt.pl - Polskie Centrum OpenWrt
o p e n (your) r o u t e r . p l
|
| |
|
|
| dawidt |
Dodano 05-04-2007 15:43
|
User
Posty: 52
Dołączył: 12/11/2006 17:47
|
moj obraz z cala pewnoscia ma pppoe poniewaz mam je do wyboru w opcjach interfejsu www  problem polaga na tym ze router nie chce ustanowic polaczenia, dane do polaczenia wpisuje na 100% dobrze...[wklejam je].
Musze popelniac jakis blad lub czegos nie robic z routerem zaraz po instalacji openWRT ;/
modem jest skonfigurowany poprawnie poniewaz bezproblemowo wszystko dzialalo na Olegu oraz na oryginalnym sofcie
Pozdrawiam
__________________________________
1000/1000@ER-X+2xArcherC7(AP)
|
| |
|
|
| arteq |
Dodano 05-04-2007 16:25
|
VIP
Posty: 1918
Dołączył: 04/03/2006 17:42
|
zobacz w konsoli poleceniem logread czy łaczy sie po pppoe spróboj tez
echo 1 > /proc/sys/net/ipv4/ip_forward
reboot
w konsoli
Pozdrawiam, Artur
http://digi-led.pl Elementy elektroniczne | urz?dzenia sieciowe | us?ugi informatyczne
http://openwrt.pl - Polskie Centrum OpenWrt
o p e n (your) r o u t e r . p l
|
| |
|
|
| dawidt |
Dodano 05-04-2007 18:09
|
User
Posty: 52
Dołączył: 12/11/2006 17:47
|
vailable.
Jan 1 00:00:06 (none) kern.warn kernel: POSIX conformance testing by UNIFIX
Jan 1 00:00:06 (none) kern.warn kernel: PCI: Fixing up bus 0
Jan 1 00:00:06 (none) kern.warn kernel: PCI: Fixing up bridge
Jan 1 00:00:06 (none) kern.debug kernel: PCI: Setting latency timer of device 0 1:00.0 to 64
Jan 1 00:00:06 (none) kern.warn kernel: PCI: Fixing up bus 1
Jan 1 00:00:06 (none) kern.info kernel: Linux NET4.0 for Linux 2.4
Jan 1 00:00:06 (none) kern.info kernel: Based upon Swansea University Computer Society NET3.039
Jan 1 00:00:06 (none) kern.warn kernel: Initializing RT netlink socket
Jan 1 00:00:06 (none) kern.warn kernel: Starting kswapd
Jan 1 00:00:06 (none) kern.warn kernel: Registering mini_fo version $Id$
Jan 1 00:00:06 (none) kern.info kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
Jan 1 00:00:06 (none) kern.info kernel: devfs: boot_options: 0x1
Jan 1 00:00:06 (none) kern.notice kernel: JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
Jan 1 00:00:06 (none) kern.info kernel: Squashfs 2.1-r2 (released 2004/12/15) ( C) 2002-2004 Phillip Lougher
Jan 1 00:00:06 (none) kern.warn kernel: pty: 256 Unix98 ptys configured
Jan 1 00:00:06 (none) kern.info kernel: Serial driver version 5.05c (2001-07-08 ) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Jan 1 00:00:06 (none) kern.info kernel: ttyS00 at 0xb8000300 (irq = 3) is a 165 50A
Jan 1 00:00:06 (none) kern.info kernel: ttyS01 at 0xb8000400 (irq = 0) is a 165 50A
Jan 1 00:00:06 (none) kern.info kernel: b44.c:v0.93 (Mar, 2004)
Jan 1 00:00:06 (none) kern.debug kernel: PCI: Setting latency timer of device 0 0:01.0 to 64
Jan 1 00:00:06 (none) kern.info kernel: eth0: Broadcom 47xx 10/100BaseT Etherne t 00:17:31 c:09:fd
Jan 1 00:00:06 (none) kern.debug kernel: PCI: Setting latency timer of device 0 0:02.0 to 64
Jan 1 00:00:06 (none) kern.info kernel: eth1: Broadcom 47xx 10/100BaseT Etherne t 40:10:18:00:00:2d
Jan 1 00:00:06 (none) kern.debug kernel: Physically mapped flash: Found an alia s at 0x800000 for the chip at 0x0
Jan 1 00:00:06 (none) kern.debug kernel: Physically mapped flash: Found an alia s at 0x1000000 for the chip at 0x0
Jan 1 00:00:06 (none) kern.debug kernel: Physically mapped flash: Found an alia s at 0x1800000 for the chip at 0x0
Jan 1 00:00:06 (none) kern.notice kernel: Amd/Fujitsu Extended Query Table v1. 3 at 0x0040
Jan 1 00:00:06 (none) kern.notice kernel: number of CFI chips: 1
Jan 1 00:00:06 (none) kern.notice kernel: cfi_cmdset_0002: Disabling fast progr amming due to code brokenness.
Jan 1 00:00:06 (none) kern.notice kernel: Flash device: 0x800000 at 0x1c000000
Jan 1 00:00:06 (none) kern.notice kernel: bootloader size: 262144
Jan 1 00:00:06 (none) kern.info kernel: Physically mapped flash: Filesystem typ e: squashfs, size=0xfb158
Jan 1 00:00:06 (none) kern.notice kernel: Creating 5 MTD partitions on "Physica lly mapped flash":
Jan 1 00:00:06 (none) kern.notice kernel: 0x00000000-0x00040000 : "cfe"
Jan 1 00:00:06 (none) kern.notice kernel: 0x00040000-0x007f0000 : "linux"
Jan 1 00:00:06 (none) kern.notice kernel: 0x000be400-0x001c0000 : "rootfs"
Jan 1 00:00:06 (none) kern.warn kernel: mtd: partition "rootfs" doesn't start o n an erase block boundary -- force read-only
Jan 1 00:00:06 (none) kern.notice kernel: 0x007f0000-0x00800000 : "nvram"
Jan 1 00:00:06 (none) kern.notice kernel: 0x001c0000-0x007f0000 : "OpenWrt"
Jan 1 00:00:06 (none) kern.info kernel: Initializing Cryptographic API
Jan 1 00:00:06 (none) kern.info kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Jan 1 00:00:06 (none) kern.info kernel: IP Protocols: ICMP, UDP, TCP, IGMP
Jan 1 00:00:06 (none) kern.info kernel: IP: routing cache hash table of 512 buc kets, 4Kbytes
Jan 1 00:00:06 (none) kern.info kernel: TCP: Hash tables configured (establishe d 2048 bind 4096)
Jan 1 00:00:06 (none) kern.warn kernel: ip_conntrack version 2.1 (5953 buckets, 5953 max) - 332 bytes per conntrack
Jan 1 00:00:06 (none) kern.warn kernel: ip_tables: (C) 2000-2002 Netfilter core team
Jan 1 00:00:06 (none) kern.info kernel: NET4: Unix domain sockets 1.0/SMP for L inux NET4.0.
Jan 1 00:00:06 (none) kern.info kernel: NET4: Ethernet Bridge 008 for NET4.0
Jan 1 00:00:06 (none) kern.info kernel: 802.1Q VLAN Support v1.8 Ben Greear
Jan 1 00:00:06 (none) kern.info kernel: All bugs added by David S. Miller
Jan 1 00:00:06 (none) kern.warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 00:00:06 (none) kern.info kernel: Mounted devfs on /dev
Jan 1 00:00:06 (none) kern.info kernel: Freeing unused kernel memory: 80k freed
Jan 1 00:00:06 (none) kern.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 00:00:06 (none) kern.warn kernel: diag: Detected 'ASUS WL-500g Premium'
Jan 1 00:00:06 (none) kern.warn kernel: Probing device eth0: found!
Jan 1 00:00:06 (none) kern.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Jan 1 00:00:06 (none) kern.info kernel: b44: eth0: Flow control is off for TX a nd off for RX.
Jan 1 00:00:06 (none) kern.info kernel: mini_fo: using base directory
Jan 1 00:00:06 (none) kern.info kernel: mini_fo: using storage directoryjffs
Jan 1 00:00:06 (none) user.info : [: missing ]
Jan 1 00:00:08 (none) kern.warn kernel: jffs2.bbc: SIZE compression mode activa ted.
Jan 1 00:00:09 (none) kern.debug kernel: PCI: Setting latency timer of device 0 1:02.0 to 64
Jan 1 00:00:09 (none) kern.warn kernel: PCI: Enabling device 01:02.0 (0004 -> 0 006)
Jan 1 00:00:09 (none) kern.warn kernel: eth2: Broadcom BCM4318 802.11 Wireless Controller 3.90.37.0
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/wl.o
Jan 1 00:00:09 (none) user.info : Warning: loading wl will taint the kernel: no license
Jan 1 00:00:09 (none) user.info : See http://www.tux.org/lkml/#export-tainted for information about tainted modules
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/ip_conntrack_ftp.o
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/ip_nat_ftp.o
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/ip_conntrack_tftp.o
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/ip_nat_tftp.o
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/ip_conntrack_ftp.o
Jan 1 00:00:09 (none) user.info : insmod: A module named ip_conntrack_ftp alrea dy exists
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/ip_nat_ftp.o
Jan 1 00:00:09 (none) user.info : insmod: A module named ip_nat_ftp already exi sts
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/ip_conntrack_irc.o
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/ip_nat_irc.o
Jan 1 00:00:09 (none) user.info : Using /lib/modules/2.4.30/wlcompat.o
Jan 1 00:00:10 (none) user.info : Using /lib/modules/2.4.30/switch-core.o
Jan 1 00:00:10 (none) user.info : insmod: A module named switch-core already ex ists
Jan 1 00:00:10 (none) user.info : Using /lib/modules/2.4.30/switch-robo.o
Jan 1 00:00:10 (none) user.info : insmod: A module named switch-robo already ex ists
Jan 1 00:00:10 (none) kern.warn kernel: BFL_ENETADM not set in boardflags. Use force=1 to ignore.
Jan 1 00:00:10 (none) user.info : Using /lib/modules/2.4.30/switch-adm.o
Jan 1 00:00:10 (none) user.info : insmod: init_module: switch-adm: No such devi ce
Jan 1 00:00:10 (none) kern.info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:12 (none) kern.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Jan 1 00:00:12 (none) kern.info kernel: b44: eth0: Flow control is off for TX a nd off for RX.
Jan 1 00:00:12 (none) kern.debug kernel: vlan0: add 01:00:5e:00:00:01 mcast add ress to master interface
Jan 1 00:00:13 (none) kern.info kernel: vlan0: dev_set_promiscuity(master, 1)
Jan 1 00:00:13 (none) kern.info kernel: vlan0: dev_set_allmulti(master, 1)
Jan 1 00:00:13 (none) kern.info kernel: device eth2 entered promiscuous mode
Jan 1 00:00:13 (none) kern.info kernel: eth2: attempt to add interface with sam e source address.
Jan 1 00:00:13 (none) kern.info kernel: br0: port 2(eth2) entering learning sta te
Jan 1 00:00:13 (none) kern.info kernel: br0: port 1(vlan0) entering learning st ate
Jan 1 00:00:13 (none) kern.info kernel: br0: port 2(eth2) entering forwarding s tate
Jan 1 00:00:13 (none) kern.info kernel: br0: topology change detected, propagat ing
Jan 1 00:00:13 (none) kern.info kernel: br0: port 1(vlan0) entering forwarding state
Jan 1 00:00:13 (none) kern.info kernel: br0: topology change detected, propagat ing
Jan 1 00:00:13 (none) kern.debug kernel: vlan0: del 01:00:5e:00:00:01 mcast add ress from vlan interface
Jan 1 00:00:13 (none) kern.debug kernel: vlan0: del 01:00:5e:00:00:01 mcast add ress from master interface
Jan 1 00:00:13 (none) kern.info kernel: br0: port 1(vlan0) entering disabled st ate
Jan 1 00:00:13 (none) kern.info kernel: CSLIP: code copyright 1989 Regents of t he University of California
Jan 1 00:00:13 (none) kern.info kernel: PPP generic driver version 2.4.2
Jan 1 00:00:14 (none) kern.info kernel: b44: eth0: Link is up at 100 Mbps, full duplex.
Jan 1 00:00:14 (none) kern.info kernel: b44: eth0: Flow control is off for TX a nd off for RX.
Jan 1 00:00:14 (none) kern.info kernel: vlan0: dev_set_promiscuity(master, 1)
Jan 1 00:00:14 (none) kern.debug kernel: vlan0: add 01:00:5e:00:00:01 mcast add ress to master interface
Jan 1 00:00:14 (none) kern.info kernel: br0: port 1(vlan0) entering learning st ate
Jan 1 00:00:14 (none) kern.info kernel: br0: port 1(vlan0) entering forwarding state
Jan 1 00:00:14 (none) kern.info kernel: br0: topology change detected, propagat ing
Jan 1 00:00:14 (none) kern.info pppd[525]: Plugin rp-pppoe.so loaded.
Jan 1 00:00:14 (none) kern.notice pppd[525]: pppd 2.4.3 started by root, uid 0
Jan 1 00:00:15 (none) kern.info dropbear[533]: Running in background
Jan 1 00:00:15 (none) kern.notice crond[546]: crond 2.3.2 dillon, started, log level 8
Jan 1 00:00:23 (none) kern.info dnsmasq[568]: started, version 2.35 cachesize 1 50
Jan 1 00:00:23 (none) kern.info dnsmasq[568]: compile time options: IPv6 GNU-ge topt ISC-leasefile no-DBus no-I18N
Jan 1 00:00:23 (none) kern.info dnsmasq[568]: DHCP, IP range 192.168.1.100 -- 1 92.168.1.249, lease time 12h
Jan 1 00:00:23 (none) kern.info dnsmasq[568]: using local addresses only for do main lan
Jan 1 00:00:23 (none) kern.warn dnsmasq[568]: failed to access /tmp/resolv.conf .auto: No such file or directory
Jan 1 00:00:23 (none) kern.info dnsmasq[568]: read /etc/hosts - 1 addresses
Jan 1 00:00:23 (none) kern.err dnsmasq[568]: failed to read /etc/ethers:No such file or directory
Jan 1 00:00:29 (none) kern.warn pppd[525]: Timeout waiting for PADO packets
Jan 1 00:00:29 (none) kern.err pppd[525]: Unable to complete PPPoE Discovery
Jan 1 00:00:29 (none) kern.info pppd[525]: Exit.
Jan 1 00:00:30 (none) kern.info pppd[585]: Plugin rp-pppoe.so loaded.
Jan 1 00:00:30 (none) kern.notice pppd[585]: pppd 2.4.3 started by root, uid 0
Jan 1 00:00:31 (none) kern.info dropbear[586]: Child connection from 192.168.1. 163:1171
Jan 1 00:00:34 (none) kern.notice dropbear[586]: password auth succeeded for 'r oot' from 192.168.1.163:1171
Jan 1 00:00:45 (none) kern.warn pppd[585]: Timeout waiting for PADO packets
Jan 1 00:00:45 (none) kern.err pppd[585]: Unable to complete PPPoE Discovery
Jan 1 00:00:45 (none) kern.info pppd[585]: Exit.
Jan 1 00:00:45 (none) kern.info pppd[600]: Plugin rp-pppoe.so loaded.
Jan 1 00:00:45 (none) kern.notice pppd[600]: pppd 2.4.3 started by root, uid 0
Jan 1 00:01:00 (none) kern.warn pppd[600]: Timeout waiting for PADO packets
Jan 1 00:01:00 (none) kern.err pppd[600]: Unable to complete PPPoE Discovery
Jan 1 00:01:00 (none) kern.info pppd[600]: Exit.
Jan 1 00:01:00 (none) kern.info pppd[609]: Plugin rp-pppoe.so loaded.
Jan 1 00:01:00 (none) kern.notice pppd[609]: pppd 2.4.3 started by root, uid 0
Jan 1 00:01:15 (none) kern.warn pppd[609]: Timeout waiting for PADO packets
Jan 1 00:01:15 (none) kern.err pppd[609]: Unable to complete PPPoE Discovery
Jan 1 00:01:15 (none) kern.info pppd[609]: Exit.
Jan 1 00:01:15 (none) kern.info pppd[618]: Plugin rp-pppoe.so loaded.
Jan 1 00:01:15 (none) kern.notice pppd[618]: pppd 2.4.3 started by root, uid 0
Jan 1 00:01:17 (none) kern.info dropbear[586]: exit after auth (root): Exited n ormally
Jan 1 00:01:20 (none) kern.info dropbear[619]: Child connection from 192.168.1. 163:1173
Jan 1 00:01:23 (none) kern.notice dropbear[619]: password auth succeeded for 'r oot' from 192.168.1.163:1173
Pozdrawiam
__________________________________
1000/1000@ER-X+2xArcherC7(AP)
|
| |
|
|
| dawidt |
Dodano 05-04-2007 18:10
|
User
Posty: 52
Dołączył: 12/11/2006 17:47
|
to wszystko co udalo mi sie przekopiowac[oraz zobaczyc] przez putty
echo 1 > /proc/sys/net/ipv4/ip_forward
reboot
to niestety nie pomoglo ;/
Edytowany przez dawidt dnia 05-04-2007 18:13
Pozdrawiam
__________________________________
1000/1000@ER-X+2xArcherC7(AP)
|
| |
|
|
| arteq |
Dodano 05-04-2007 19:03
|
VIP
Posty: 1918
Dołączył: 04/03/2006 17:42
|
dziwne :/
połączenie WAN - modem jest poprawne ?
spróbój dodac ustawienia nvram dla interfejsów wg openwrt.pl
nvram set vlan1ports="0 5"
nvram set wan_ifname=vlan1
nvram set lan_ifnames="vlan0 eth2"
nvram set lan_ifname=br0
nvram commit && reboot
Pozdrawiam, Artur
http://digi-led.pl Elementy elektroniczne | urz?dzenia sieciowe | us?ugi informatyczne
http://openwrt.pl - Polskie Centrum OpenWrt
o p e n (your) r o u t e r . p l
|
| |
|
|
| dawidt |
Dodano 06-04-2007 08:54
|
User
Posty: 52
Dołączył: 12/11/2006 17:47
|
ale ja jestem ograniczony :/ dzisiaj wgralem olega i tez mi nie chcialo ruszyc. zapomnialem ze wpisujac default w lucencie kasuje ustawienia dla neo 0:35 ... ;/ sorka za zasmiecanie forum ;/
dzieki za pomoc
Pozdrawiam
__________________________________
1000/1000@ER-X+2xArcherC7(AP)
|
| |
|
|
| arteq |
Dodano 06-04-2007 09:49
|
VIP
Posty: 1918
Dołączył: 04/03/2006 17:42
|
czyli dziala juz na OpenWrt ?
Pozdrawiam, Artur
http://digi-led.pl Elementy elektroniczne | urz?dzenia sieciowe | us?ugi informatyczne
http://openwrt.pl - Polskie Centrum OpenWrt
o p e n (your) r o u t e r . p l
|
| |
|
|
| dawidt |
Dodano 06-04-2007 14:36
|
User
Posty: 52
Dołączył: 12/11/2006 17:47
|
tak dziala
na poczatku po instalacji open wrt po raz pierwszy, cos mi nie dzialalo wiec wzialem sie za modem i dalem default.... ;/
Pozdrawiam
__________________________________
1000/1000@ER-X+2xArcherC7(AP)
|
| |
|
|
| dawidt |
Dodano 09-04-2007 19:18
|
User
Posty: 52
Dołączył: 12/11/2006 17:47
|
EDIT: problem rozwiazyny
Edytowany przez dawidt dnia 10-04-2007 19:57
Pozdrawiam
__________________________________
1000/1000@ER-X+2xArcherC7(AP)
|
| |
|
' target='_blank'>Link
